Eachine Tyro99 210mm DIY Version FPV Racing RC Drone F4 OSD 30A BLHeli_S 40CH 600mW VTX 700TVL Camera

$164.99

Instock
- +

Description

Note:
1. This is the DIY version that comes unassembled.
2. Make sure the antenna is installed at the output end before powering up to avoid damaging internal components;
3. Note that the input voltage is within the specified range and is correct and correct to avoid damaging internal components;
4. If the antenna is replaced, select a standing wave and a gain antenna for a longer transmission distance;
5. Pay attention to classic protection during transportation and installation.
6. Take-off weight is about 450g.

Item Specification
210mm Frame Kit
Wheel base: 210mm
Frame arm thickness: 5mm
Bottom plate thickness: 2mm
Side plate thickness: 2mm
Frame kit material: 3K carbon fiber & 6065 aluminium
2206 2150KV Brushless Motor
Motor KV: 2150RPM/V
Idle current (Io/10V): 1.26A
Lipo cell: 3-5S
Weight: 31g
Max continuous current: 31A
Max continuous power: 496W
Max thrust: 1050g (4S/5″)
Configu-ration: 12N/14P
Motor resistance (RM): 0.0572 Ω
Stator diameter: 22mm
Stator thickness: 6mm
Motor diameter: 27.7mm
Motor body length: 19.2mm
Overall shaft length: 34.2mm
Prop adapter shaft: M5
Bolt holes spacing: 16mm
Bolt thread: M3
Propeller: 5-6 inch
4 IN 1 30A BLHeli_S ESC
Continuous current: 30A
Burst Current: 40A(10S)
Input voltage: 2-5S
BEC: 5V 2A BEC
Main control chip: 48Mhz EFM8BB2
Firmware: BLHeli_S supports Dshot600
MOS: 5*6
New F4 Flight Controller ( More Details, Click Here)
Main control chip: STM32F405
Sensor: ICM20602
Power supply: 5V
Integrated OSD
Onboard LC filter
PID cycle rate & gyroscope refresh rate up to 32Khz
Supports BetaFlight / inav racing firmware
700TVL CMOS Camera
Case size: 25mm*25mm
Weight: 9.5g
Total pixels: PAL: 1020H×596V (0.61MP); NTSC: 1020H×508V (0.52MP)
Effective pixels: PAL: 976H×582V (0.57MP); NTSC: 976H×494V (0.48MP)
Signal system: NTSC
Resolution ratio(horizontal center): 700TVL
Video output: 1.0Vp-p/75Ω

Automatic gain control: 0.25/0.50/0.75/1.00, up to 55dB
White balance: on/off optional
Exposure mode: electron exposure
Electronic shutter: 1/50(1/60) – 1/100000 S
Gamma correction: 0.45/1.0
Synchronization method: inter-sync
Camera lens: standard 2.8mm
Lens operating voltage: DC12V (wide voltage, measured can work normally at 7.5-13V)
Working current: 70mA (low power consumption)
Working temperature: -20℃~-60℃
Humidity: 0%~98%
5.8G 40CH 0/25/200/600mw switchable VTX ( New Version, more Details Link)
Output power & transmission distance: ≥[email protected], ≥[email protected], ≥[email protected]
Transmitting power: 0mW/25mW/200mW/600mW
Full video format: NTSC /PAL
Input voltage & power dissipation: 7V~24V, +12V/[email protected]
Size: 20*30*9mm
Weight: ≤7g(except antenna)
With output power self-check function.
Nixie tube SCAN: frequency point (1-8), frequency band (A-E), power (1-3, 0=0mw, 1=25mw, 2=200mw, 3=600mw)
Racerstar 5040 2 Blade Propeller
Material: PC
Mounting hole: 5mm
Quantity: 2 CW & 2 CCW
Color: blue, red, yellow, purple, white (Delivery color randomly 
Battery Not included
Recommend 3-5S
Package included:
1 x 210mm frame kit
2 x 2206 2150KV brushless motor CW
2 x 2206 2150KV brushless motor CCW
1 x 4 IN 1 30A BLHeli_S ESC
1 x New F4 flight controller
1 x 700TVL CMOS camera
1 x New VTX
2 x Battery strap
2 x Racerstar 5038 2 blade propeller CW
2 x Racerstar 5038 2 blade propeller CCW

 

Shopping Cart Items

Empty cart

No products in the cart.

Return to Shop
Search for: